Installation Components
Tools, Tek-Screws & Drivers
Aviation Snips
KJS1 – Right
KJS2 – Left
Guarantee
Every Klenk Tool carries a lifetime guarantee against breakage. Should the blades break in normal use, the tool will be replaced by the Klenk distributor, or may be returned to the factory for repair or replacement. Factory reconditioning and resharpening service is also available at a very nominal charge.
Aviation Snips
- Made of hard Molybdenum/Silicon tool steel for good cutting edge and longer tool life
- Double-cam-action construction for 20% greater cutting power with less effort, maximum opening of jaws, minimum opening of handles
- Serrated blades – Draw work into cutting edges without slipping, for accurate, clean cuts
- Higher leverage, spring-action handles
- Hardened pivot bolt; safety latch; self-locking nuts
- Soil and wear-resistant PVC grips
- Left hand model – green – cuts right
- Right hand model – red – cuts left
- Straight – yellow – cuts straight and slight curves
| Aviation Snips Ordering Information | ||||||||||||
|
Tek-Screws and Drivers
Tek-Screws: Used as a self-drilling screw they eliminate all hole preparation. Tek-Screws can be used with or without pilot holes. Positive rake forward cutting edges drills straight thru sheet metal at peak speed. Perfectly mated threads increase strip and back out pressures. Used extensively by installers of heating and ventilating duct to produce sheet metal assemblies faster and more securely.
Tek-Screw Driver (TSD)
1/4” driver for #8 Tek-Screw
Tek-Screw
#8 x 1/2”
Available in quantities of
50, 100, 500, 1000
Angle Rings, Flange Clamps & Spiralmate®
| Inside Dia. | H | W | T | Bolt Hole Centers | No. of Bolt Holes | Dia. of Bolt Holes | Weight (lbs.) | |
| Pressed | 3-1/16″ | 7/8″ | 1″ | 10 Ga. | 4-5/16″ | 6 | 9/32″ | .70 |
| 4-1/16 | 15/16″ | 1″ | 10 Ga. | 5-5/16″ | 6 | 9/32″ | .85 | |
| 5-1/16′ | 1″ | 1″ | 10 Ga. | 6-5/16″ | 6 | 3/8″ | 1.20 | |
| Rolled Angle | 6-1/8″ | 1-1/4″ | 1-1/4″ | 10 Ga. | 7-1/2″ | 6 | 3/8″ | 1.75 |
| 7-1/8″ | 1-1/4″ | 1-1/4″ | 10 Ga. | 8-1/2″ | 6 | 3/8″ | 2.00 | |
| 8-1/8″ | 1-1/4″ | 1-1/4″ | 10 Ga. | 9-1/2″ | 8 | 3/8″ | 2.25 | |
| 9-1/8″ | 1-1/4″ | 1-1/4″ | 10 Ga. | 10-1/2 | 8 | 3/8″ | 2.50 | |
| 10-1/8″ | 1-1/4″ | 1-1/4″ | 10 Ga. | 11-1/2″ | 8 | 3/8″ | 2.75 | |
| 11-1/8″ | 1-1/4″ | 1-1/4″ | 10 Ga. | 12-1/2″ | 8 | 7/16″ | 3.00 | |
| 12-3/16″ | 1-1/2″ | 1-1/2″ | 10 Ga. | 13-13/16″ | 12 | 7/16″ | 4.00 | |
| 13-3/16″ | 1-1/2″ | 1-1/2″ | 10 Ga. | 14-13/16″ | 12 | 7/16″ | 4.25 | |
| 14-3/16″ | 1-1/2″ | 1-1/2″ | 10 Ga. | 15-13/16″ | 12 | 7/16″ | 4.75 | |
| 15-3/16″ | 1-1/2″ | 1-1/2″ | 10 Ga. | 16-13/16″ | 16 | 7/16″ | 5.0 | |
| 16-3/16″ | 1-1/2″ | 1-1/2″ | 3/16″ | 18-1/8″ | 16 | 7/16″ | 8.0 | |
| 17-3/16″ | 1-1/2″ | 1-1/2″ | 3/16″ | 19-1/8″ | 16 | 7/16″ | 8.25 | |
| 18-3/16″ | 1-1/2″ | 1-1/2″ | 3/16″ | 20-1/8″ | 16 | 7/16″ | 8.50 | |
| 20-3/16″ | 1-1/2″ | 1-1/2″ | 3/16″ | 22-1/8″ | 20 | 7/16″ | 9.50 | |
| 22-3/16″ | 1-1/2″ | 1-1/2″ | 3/16″ | 24-1/8″ | 20 | 7/16″ | 10.75 | |
| 24-3/16″ | 1-1/2″ | 1-1/2″ | 3/16″ | 26-1/8″ | 20 | 7/16″ | 11.50 | |
| 26-3/16″ | 2″ | 2″ | 3/16″ | 28-1/2″ | 24 | 7/16″ | 16.50 | |
| 28-3/16″ | 2″ | 2″ | 3/16″ | 30-1/2″ | 24 | 7/16″ | 18.00 | |
| 30-3/16″ | 2″ | 2″ | 3/16″ | 32-1/2″ | 28 | 7/16″ | 19.50 | |
| 32-3/16″ | 2″ | 2″ | 3/16″ | 34-1/2″ | 28 | 7/16″ | 20.00 | |
| 34-3/16″ | 2″ | 2″ | 3/16″ | 36-1/2″ | 32 | 7/16″ | 22.50 | |
| 36-3/16″ | 2″ | 2″ | 3/16″ | 38-1/2″ | 32 | 7/16″ | 23.00 | |
| 38-3/16″ | 2″ | 2″ | 3/16″ | 40-1/2″ | 36 | 7/16″ | 24.50 | |
| 40-3/16″ | 2″ | 2″ | 3/16″ | 42-1/2″ | 36 | 7/16″ | 25.75 | |
| 42-3/16″ | 2″ | 2″ | 3/16″ | 44-1/2″ | 40 | 7/16″ | 26.50 | |
| 44-3/16″ | 2″ | 2″ | 3/16″ | 46-1/2″ | 40 | 7/16″ | 28.00 | |
| 46-3/16″ | 2″ | 2″ | 3/16″ | 48-1/2″ | 44 | 7/16″ | 29.00 | |
| 48-3/16″ | 2″ | 2″ | 3/16″ | 50-1/2″ | 44 | 7/16″ | 30.75 |
Angle Rings
(Pressed or Rolled Steel)
Pressed and rolled steel angle rings are used widely in joining ductwork together in dust and fume control work. All rings are unpainted, mild steel (Galvanized and Stainless Steel available). They are available with or without holes.
Dimensions shown are typical. Nearly any bolt circle or hole size is available. Consult Factory.
