Installation Components  
 

     Tools, Tek-Screws & Drivers

Aviation Snips

• Made of hard Molybdenum/Silicon tool steel for
good cutting edge and longer tool life
• Double-cam-action construction for 20% greater
cutting power with less effort, maximum opening of jaws, minimum opening of handles
• Serrated blades - Draw work into cutting edges
without slipping, for accurate, clean cuts
• Higher leverage, spring-action handles
• Hardened pivot bolt; safety latch; self-locking nuts
• Soil and wear-resistant PVC grips
• Left hand model - green - cuts right
• Right hand model - red - cuts left
• Straight - yellow - cuts straight and slight curves

Aviation Snips Ordering Information
Model No. Description Length Cut
KJS1 Right Hand 9-12" 1-1/4"
3.2 cm
KJS2 Left Hand 9-1/2" 1-1/4"
3.2 cm

Tek-Screws and Drivers

Tek-Screws: Used as a self-drilling screw they eliminate all hole preparation. Tek-Screws can be used with or without pilot holes. Positive rake forward cutting edges drills straight thru sheet metal at peak speed. Perfectly mated threads increase strip and back out pressures. Used extensively by installers of heating and ventilating duct to produce sheet metal
assemblies faster and more securely.

Tek-Screw Driver (TSD)
1/4” driver for #8 Tek-Screw

  

KJS1 - Right

KJS2 - Left

Guarantee
Every Klenk Tool carries a lifetime guarantee against breakage. Should the blades break in normal use, the tool will be replaced by the Klenk distributor, or may be returned to the factory for repair or replacement. Factory reconditioning and resharpening service is also available at a very nominal charge.

Tek-Screw
#8 x 1/2”

Available in quantities of
50, 100, 500, 1000

 

Angle Rings, Flange Clamps & Spiralmate®       

Installation Components  

 

 

  Inside Dia. H W T Bolt Hole Centers No. of Bolt Holes Dia. of Bolt Holes Weight (lbs.)
Pressed 3-1/16" 7/8" 1" 10 Ga. 4-5/16" 6 9/32" .70
4-1/16 15/16" 1" 10 Ga. 5-5/16" 6 9/32" .85
5-1/16' 1" 1" 10 Ga. 6-5/16" 6 3/8" 1.20
Rolled Angle 6-1/8" 1-1/4" 1-1/4" 10 Ga. 7-1/2" 6 3/8" 1.75
7-1/8" 1-1/4" 1-1/4" 10 Ga. 8-1/2" 6 3/8" 2.00
8-1/8" 1-1/4" 1-1/4" 10 Ga. 9-1/2" 8 3/8" 2.25
9-1/8" 1-1/4" 1-1/4" 10 Ga. 10-1/2 8 3/8" 2.50
10-1/8" 1-1/4" 1-1/4" 10 Ga. 11-1/2" 8 3/8" 2.75
11-1/8" 1-1/4" 1-1/4" 10 Ga. 12-1/2" 8 7/16" 3.00
12-3/16" 1-1/2" 1-1/2" 10 Ga. 13-13/16" 12 7/16" 4.00
13-3/16" 1-1/2" 1-1/2" 10 Ga. 14-13/16" 12 7/16" 4.25
14-3/16" 1-1/2" 1-1/2" 10 Ga. 15-13/16" 12 7/16" 4.75
15-3/16" 1-1/2" 1-1/2" 10 Ga. 16-13/16" 16 7/16" 5.0
16-3/16" 1-1/2" 1-1/2" 3/16" 18-1/8" 16 7/16" 8.0
17-3/16" 1-1/2" 1-1/2" 3/16" 19-1/8" 16 7/16" 8.25
18-3/16" 1-1/2" 1-1/2" 3/16" 20-1/8" 16 7/16" 8.50
20-3/16" 1-1/2" 1-1/2" 3/16" 22-1/8" 20 7/16" 9.50
22-3/16" 1-1/2" 1-1/2" 3/16" 24-1/8" 20 7/16" 10.75
24-3/16" 2" 2" 3/16" 26-1/8" 20 7/16" 11.50
26-3/16" 2" 2" 3/16" 28-1/2" 24 7/16" 16.50
28-3/16" 2" 2" 3/16" 30-1/2" 24 7/16" 18.00
30-3/16" 2" 2" 3/16" 32-1/2" 28 7/16" 19.50
32-3/16" 2" 2" 3/16" 34-1/2" 28 7/16" 20.00
34-3/16" 2" 2" 3/16" 36-1/2" 32 7/16" 22.50
  36-3/16" 2" 2" 3/16" 38-1/2" 32 7/16" 23.00
38-3/16" 2" 2" 3/16" 40-1/2" 36 7/16" 24.50
40-3/16" 2" 2" 3/16" 42-1/2" 36 7/16" 25.75
42-3/16" 2" 2" 3/16" 44-1/2" 40 7/16" 26.50
44-3/16" 2" 2" 3/16" 46-1/2" 40 7/16" 28.00
46-3/16" 2" 2" 3/16" 48-1/2" 44 7/16" 29.00
48-3/16" 2" 2" 3/16" 50-1/2" 44 7/16" 30.75
 

Angle Rings
(Pressed or Rolled Steel)

Pressed and rolled steel angle
rings are used widely in joining
ductwork together in dust and
fume control work. All rings are
unpainted, mild steel (Galvanized
and Stainless Steel available). They
are available with or without holes.
Dimensions shown are typical.
Nearly any bolt circle or hole size is
available. Consult Factory.
     
Spiralmate® Flange Quick Sleeve Flange Clamps
  [Back to top]  
11419 Yellowpine St. NW - Minneapolis, MN 55448 - Ph: 763-755-7677 - 1-800-426-3643 - info@spiralmfg.com